Do not attempt to run this program over Wi-Fi or a network sharing setup. Connect your Epson 1410 directly to your computer using a high-quality USB cable.
Once the printer’s internal "waste ink pad counter" hits its maximum manufacturer limit, the printer will refuse to print, and you will be met with blinking red lights and a "Service Required" warning on your computer. This is a built-in fail-safe to prevent ink from overflowing and damaging the internal components.
If you see in the adjustment program interface (e.g., a checkbox or error log), it often means the printer has logged a cover or carriage position fault in EEPROM. Resetting EPROM can clear that flag, allowing the printer to initialize again.
This is a legacy service tool often used by technicians. It requires extracting the files and sometimes setting your PC's internal date back to roughly 2007 for the software to boot properly.
The most common reason for a printer lockout.
Click the large button on the right side of the main menu interface. A long list of maintenance operations will appear. Step 5: Select the Waste Ink Pad Counter
Resetting the Epson Stylus Photo 1410 waste ink pad counter requires the dedicated Adjustment Program (AdjProg) to resolve "Service Required" errors, often necessitating that antivirus be disabled and the system date changed to Nov 2007. The procedure involves selecting the printer in the software, choosing "Waste Ink Pad Counter," running the "Initialization" function, and restarting the printer. For the full, original manual and service utility, visit 2Manuals.com Waste Ink Counter reset - Epson Service Adjustment Programs
Disconnect all other USB peripherals (like secondary scanners, other printers, or external hard drives) to prevent the software from probing the wrong hardware port.
Epson programs a digital counter inside the printer’s EEPROM (Electrically Erasable Programmable Read-Only Memory) chip to estimate when these physical pads will become fully saturated with liquid ink. If the printer allowed you to keep printing indefinitely, excess ink would eventually overflow the pads, leak out of the bottom of the printer casing, and ruin your desk, carpets, or internal electronic circuitry.
is set to your specific printer (don't leave it on "Auto Selection"). Enter Service Mode: Particular Adjustment Mode Find the Counter: Scroll down to the Maintenance section and select Waste ink pad counter , then click Phase 3: The EEPROM Reset Now for the actual "reset" part: Check Status:
Select , navigate to the Compatibility tab, check the box for "Run this program in compatibility mode for," and select Windows 7 . Check the box at the bottom for "Run this program as an administrator." Click Apply and OK. Double-click AdjProg.exe to open the software. Step 2: Configure the Port Settings
Resetting the EEPROM only resets the digital counter; it does not physically clean or empty the waste ink pads.
Do not attempt to run this program over Wi-Fi or a network sharing setup. Connect your Epson 1410 directly to your computer using a high-quality USB cable.
Once the printer’s internal "waste ink pad counter" hits its maximum manufacturer limit, the printer will refuse to print, and you will be met with blinking red lights and a "Service Required" warning on your computer. This is a built-in fail-safe to prevent ink from overflowing and damaging the internal components.
If you see in the adjustment program interface (e.g., a checkbox or error log), it often means the printer has logged a cover or carriage position fault in EEPROM. Resetting EPROM can clear that flag, allowing the printer to initialize again.
This is a legacy service tool often used by technicians. It requires extracting the files and sometimes setting your PC's internal date back to roughly 2007 for the software to boot properly. reset eprom epson 1410 adjustment program top
The most common reason for a printer lockout.
Click the large button on the right side of the main menu interface. A long list of maintenance operations will appear. Step 5: Select the Waste Ink Pad Counter
Resetting the Epson Stylus Photo 1410 waste ink pad counter requires the dedicated Adjustment Program (AdjProg) to resolve "Service Required" errors, often necessitating that antivirus be disabled and the system date changed to Nov 2007. The procedure involves selecting the printer in the software, choosing "Waste Ink Pad Counter," running the "Initialization" function, and restarting the printer. For the full, original manual and service utility, visit 2Manuals.com Waste Ink Counter reset - Epson Service Adjustment Programs Do not attempt to run this program over
Disconnect all other USB peripherals (like secondary scanners, other printers, or external hard drives) to prevent the software from probing the wrong hardware port.
Epson programs a digital counter inside the printer’s EEPROM (Electrically Erasable Programmable Read-Only Memory) chip to estimate when these physical pads will become fully saturated with liquid ink. If the printer allowed you to keep printing indefinitely, excess ink would eventually overflow the pads, leak out of the bottom of the printer casing, and ruin your desk, carpets, or internal electronic circuitry.
is set to your specific printer (don't leave it on "Auto Selection"). Enter Service Mode: Particular Adjustment Mode Find the Counter: Scroll down to the Maintenance section and select Waste ink pad counter , then click Phase 3: The EEPROM Reset Now for the actual "reset" part: Check Status: This is a built-in fail-safe to prevent ink
Select , navigate to the Compatibility tab, check the box for "Run this program in compatibility mode for," and select Windows 7 . Check the box at the bottom for "Run this program as an administrator." Click Apply and OK. Double-click AdjProg.exe to open the software. Step 2: Configure the Port Settings
Resetting the EEPROM only resets the digital counter; it does not physically clean or empty the waste ink pads.